View AAT462608_4858189.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRODUCT DATASHEET
AAT4626
SmartSwitchTM
General Description
The AAT4626 SmartSwitch is part of AnalogicTech's Application Specific Power MOSFETTM (ASPMTM) product family. It is a dual-channel 500mA current-limited P-channel MOSFET power switch designed for high-side load switching applications. This switch operates with inputs ranging from 2.7V to 5.5V, making it ideal for both 3V and 5V systems. An integrated current-limiting circuit protects the input supply against large changes in load current which may cause the supply to fall out of regulation. The AAT4626 is also protected from thermal overload which limits power dissipation and junction temperatures. The current limit threshold is factory programmed at 1.0A, with a maximum of 1.5A. The quiescent supply current is typically a low 20A. In shutdown mode, the supply current decreases to less than 1A. The AAT4626 is available in a Pb-free, 8-pin SOP or TSSOP package and is specified over the -40C to +85C temperature range. The AAT4600 series is a family of adjustable and fixed SmartSwitch products with a range of current handling capabilities. Single versions are available with adjustable current limit (AAT4601) or fixed current limit (AAT4625), as well as dual versions with fixed current limit (AAT4626).
USB Dual-Channel Power Switch
Features
* * * * * * 2.7V to 5.5V Input Voltage Range Compliant to USB 1.1 and 2.0 Specifications 500mA (Min) Continuous Current per Channel 1.25A (Max) Current Limit per Channel 90m Typical RDS(ON) Low Quiescent Current: Typically 20A 1A Max with Switches Off Thermal Shutdown Slew Rate Limited Turn On Fault Flag with 2ms Blanking Under-Voltage Lockout Temperature Range: -40C to +85C UL Approved--File No. E217765 8-Pin SOP or TSSOP Package
* * * * * * *
Applications
* * * * General-Purpose Power Switching Hot Swap Supplies Notebook Computers USB Ports and Peripherals
UL Recognized Component
Typical Application
100k 100k VCC 5.0V ENA (ENA) ENB 0.1F (ENB)
7
IN ENA (ENA) ENB (ENB) GND
6
FLGA
2 3 8 5
1
AAT4626
FLGB OUTA OUTB
OUTPUTA OUTPUTB
4
47F GND
47F GND
4626.2008.02.1.3
www.analogictech.com
1
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Pin Descriptions
Pin #
1, 4 2,3 5, 8 6 7
USB Dual-Channel Power Switch
Symbol
EN(A/B) (EN(A/B)) FLG(A/B) OUT(A/B) GND IN
Function
Enable inputs: logic-compatible enable input. High input > 2.1V typical. Low input < 1.9V typical. Active high or active low option available; see Ordering Information for details. Fault flag outputs: active-low, open-drain output. Indicates over-current, UVLO, and thermal shutdown. Switch outputs: these pins are the P-channel MOSFET drain connection. Ground connection. Supply input: this pin is the source connection for the P-channel MOSFETs. Also supplies the IC's internal circuitry.
Pin Configuration
SOP-8 (Top View) TSSOP-8 (Top View)
ENA (ENA) FLGA FLGB ENB (ENB)
1
8
OUTA IN GND OUTB
1
ENA (ENA) FLGA FLGB ENB (ENB)
1 2 3 4
8 7 6 5
OUTA IN GND OUTB
2
7
2
3
6
4
5
2
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Absolute Maximum Ratings1
TA = 25C, unless otherwise noted. Symbol
VIN VFLG IFLG VOUT IOUT VEN TJ TS TLEAD
USB Dual-Channel Power Switch
Description
IN to GND FLGA, FLGB to GND FLGA, FLGB Current OUTA, OUTB to GND Output Current EN (EN) to GND Operating Junction Temperature Range Storage Temperature Maximum Soldering Temperature (at Leads)
Value
-0.3 to 6 -0.3 to 6 50 -0.3 to VIN + 0.3 Internally Limited -0.3 to 6 -40 to 150 150 300
Units
V V mA V A V C C C
Thermal Information2
Symbol
JA PD
Description
Maximum Thermal Resistance (SOP-8) Maximum Power Dissipation (SOP-8)
Value
100 1.25
Units
C/W W
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 printed circuit board with 1 oz. copper ground plane.
4626.2008.02.1.3
www.analogictech.com
3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Electrical Characteristics
USB Dual-Channel Power Switch
VIN = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C; bold values designate full temperature range. Symbol
IQ VIN-THRSH IEN CEN RDS(ON) TON TON-RISE TOFF TOFF-FALL ISD(OFF) ILIMIT OTMP RFLG ISINK VUVLO TBLANK
Description
Quiescent Current Enable Input Threshold Enable Input Current Enable Input Capacitance On-Resistance Output Turn-On Delay Output Turn-On Rise Time Output Turn-Off Delay Output Turn-Off Fall Time Output Leakage Current Current Limit Threshold Over-Temperature Shutdown Error Flag Output Resistance Error Flag Off Current Under-Voltage Lockout Fault Blanking
Conditions
VIN = 5V, ENA and ENB Active Low-to-High Transition High-to-Low Transition VEN = 0V to 5.5V VIN = 5V, Each Switch, TA = 25C VIN =3.0V, Each Switch, TA = 25C VIN = 5V, RL = 10 RL = 10 VIN = 5V, RL = 10 RL = 10 EN = Inactive, VIN = 5.5V, VOUT = 0V Ramped Load Applied to Enable Output, VOUT < 4.0V TJ Increasing TJ Decreasing VIN = 5V, IL = 1mA VFLG = 5.5V VIN = Increasing, 1% Hysteresis
Min
Typ
20
Max
40 2.4 1 130 150
Units
A V A pF m ms ms s s A A C
0.8 0.01 1 90 100 0.25 0.2 5 0.03 1.0 125 115 30 0.05 2.3 2
0.75
20 20 1 1.50
2.0
1 2.7
A V ms
4
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Typical Characteristics
Unless otherwise noted, VIN = 5V, TA = 25C.
USB Dual-Channel Power Switch
Quiescent Current vs. Temperature
Quiescent Current (A)
30 25 20 15 10 5 0 -40 -20 0 20 40 60 80 100 120
25
Quiescent Current
Input Current (A)
20 15 10 5 0 0 1
2 channels enabled
1 channel enabled
2
3
4
5
6
Temperature (C)
Input Voltage (V)
Current Limit
1.4
1.0000
Off-Supply Current vs. Temperature
Output Current (A)
1.2 1 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5
Off-Switch Current (A)
0.1000
0.0100
0.0010 -40 -20 0 20 40 60 80 100 120
Output Voltage (V)
Temperature (C)
Off-Switch Current vs. Temperature
1.0000
140.0
RDS(ON) vs. Temperature
Off-Switch Current (A)
(Both switches)
0.1000
130.0
RDS(ON) (m)
120.0 110.0 100.0 90.0 80.0 70.0 60.0
0.0100
VIN = 3V VIN = 5V
0.0010
0.0001
0.0000 -40 -20 0 20 40 60 80 100 120
-40
-20
0
20
40
60
80
100
120
Temperature (C)
Temperature (C)
4626.2008.02.1.3
www.analogictech.com
5
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Typical Characteristics
Unless otherwise noted, VIN = 5V, TA = 25C.
USB Dual-Channel Power Switch
Turn-On/Off Response with 10, 1F Load
Start Into 1 Load
EN (5V/div) EN (5V/div) FAULT (5V/div) FAULT (5V/div) VOUT (1V/div) VOUT (1V/div)
IIN (500mA/div) IIN (500mA/div)
Time (200s/div) Time (100s/div)
Thermal Shutdown Response
Short Circuit Through 0.3
8 12
EN (5V/div) Input and Output (V)
FAULT (5V/div)
6
Input Voltage
8
Output (A)
4
VOUT (1V/div) IIN (500mA/div)
Output Current Output Voltage
4
2
0
0 -1 0 1 2 3 4 5
-4
Time (100ms/div) Time (s)
Short Circuit Through 0.6
Input and Output (V)
6
Input Voltage
4
6
Output (A)
Output Current
3
2
Output Voltage
0
0 -1 0 1 2 3 4 5
-3
Time (s)
6
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Functional Block Diagram
USB Dual-Channel Power Switch
IN
OverTemperature Protection UnderVoltage Lockout
OUTA OUTB
ENB (ENB) ENA (ENA)
1.2V Reference Current Limit
Over-Temp Protection Under-Voltage Lockout Current Limit
FLGA
Over-Temp Protection Under-Voltage Lockout Current Limit
FLGB
Functional Description
The AAT4626 is a dual integrated MOSFET load switch with a fixed level current limit, over-temperature protection, level shifted inputs, and a fault flag for each switch. The current limit control is combined with an over-temperature thermal limit circuit to provide a comprehensive system to protect the load switch under short-circuit or other adverse operating conditions. The AAT4626 is ideally suited for control and protection of peripheral ports such as USB, RS232, and parallel ports. The current limit and over-temperature circuits will act independently. The device current limit is activated when the output load current exceeds a preset internal threshold level. The minimum current limit threshold characteristic is specified by ILIM(MIN). If the load switch ambient temperature becomes excessive or if a short-circuit condition persists, the die temperature will rise, causing the over-temperature protection circuit to activate. If the current limit or over-temperature protection circuits are active for more than ten milliseconds, the sys-
tem will be informed via the FAULT flag. The ten millisecond fault blanking delay allows the AAT4626 to be turned on into large capacitive loads without activating the FAULT flags. The open drain FAULT outputs can be connected directly to system controllers driven by voltage levels less than the IN pin voltage without additional level shifting circuitry. Each of the two load switches is turned on and off by applying a logic level signal to the EN(A/B) pin. The AAT4626 enable function is available in both active high and active low logic level versions. The AAT4626 typically consumes 20A when operating; when off, the device draws less than 1A. In the off state, current is prevented from flowing between the input and output on each respective channel. The EN(A/B) function has logic level thresholds that allow the AAT4626 to be TTL compatible and may also be controlled by 2.5V to 5.0V CMOS circuits. The voltage level on either EN(A/B) or FAULT(A/B) should not exceed the input supply level present on the IN pin.
4626.2008.02.1.3
www.analogictech.com
7
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Applications Information
Operation in Current Limit
If an excessive load is applied to either output of an AAT4626, the load current will be limited by the device's current limit circuitry. Refer to the "Current Limit" curve in the Typical Characteristics section of this datasheet. If a short circuit were to occur on the load applied to either the A or B output, there would be a demand for more current than what is allowed by the internal current limiting circuit and the voltage at the device output will drop. This causes the AAT4626 to dissipate more power than in normal operation, causing the die temperature to increase. When die temperature exceeds the internal over-temperature threshold, the AAT4626 will shut down both the A and B output channels. After shutting down, the AAT4626 cools to a level below the over-temperature threshold, at which point it will start up again. The AAT4626 will continue to cycle off and on until one of the following events occurs: the load current of the offending output is reduced to a level below the AAT4626's current limit setting; the input power is removed; or the output is turned off by a logic high level applied to the EN pin of the fault channel.
USB Dual-Channel Power Switch
Eq. 2: IMAX =
TSD(MIN) - TA(MAX) RDS(ON)(MAX) * RJA
TSD(MIN) is the minimum temperature required to activate the device over-temperature protection. The typical thermal limit temperature specification is 125C for the AAT4626. For calculations, 115C is a safe minimum value to use. For example, a portable device is specified to operate in a 50C environment. The printed circuit board assembly will operate at temperatures as high as 85C. This portable device has a sealed case and the area of the printed board assembly is relatively small, causing RJA to be approximately 100C/W. RDS(ON)(MAX) = 130W. Using Equation 2,
Eq. 3: IMAX =
115C - 85C = 1.25A 130W * 120C/W
If this system requires less than 1.4A, the thermal limit will not activate during normal operation.
Input Capacitor
The input capacitor serves two purposes. First, it protects the source power supply from transient current effects generated by the application load circuits. If a short circuit is suddenly applied to either output of an AAT4626, there is a microsecond long period during which a large current can flow before the current limit circuit becomes active. Refer to the Typical Characteristics curve "Short Circuit Through 0.3." A properly sized input capacitor can dramatically reduce the load switch input transient response effects seen by the power supply and other circuitry upstream from the AAT4626. The second purpose of the input capacitor is to prevent transient events generated by the load circuits from effecting the operation of the AAT4626. For example, if an AAT4626 is used in a circuit that operates from a 5V power supply with poor step load response, it is possible that turning on the load switch could cause the input power supply to droop below the AAT4626's under-voltage lockout threshold. This drop in voltage would cause the AAT4626 to turn off until the input power supply voltage levels recover. Since this cycle would be selfperpetuating, the entire circuit could be seen to be unstable. In the very rare case where capacitor cost is prohibitive and the input capacitor is omitted, the output load circuit should be slew rate limited when turned on.
Thermal Considerations
Since the AAT4626 has internal current limit and overtemperature protection, junction temperature is rarely a concern. If an application requires a large load current in a high temperature operating environment, there is the possibility that the over-temperature protection circuit rather than the current limit circuit from one of the two outputs will regulate the current available to the load. In these applications, the maximum current available without risk of activation of the over-temperature circuit can be calculated. The maximum internal temperature while current limit is not active can be calculated using Equation 1: Eq. 1: TJ(MAX) = IMAX2 * RDS(ON)(MAX) * RJA + TA(MAX) In Equation 1, IMAX is the maximum current required by the load. RDS(ON)(MAX) is the maximum rated RDS(ON) of the AAT4626 at high temperature. RJA is the thermal resistance between the device die and the board onto which it is mounted. TA(MAX) is the maximum ambient temperature for the printed circuit board assembly under the AAT4626 when the load switch is not dissipating power. Equation 1 can be transformed to provide IMAX; Refer to Equation 2.
8
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Output Capacitor
In order to insure stability while the device current limit is active, a small capacitance of approximately 1F should be used on each output. When either output of the AAT4626 is activated using the EN(A/B) function, there are no momentary current transients, as in the case when a short circuit is suddenly applied to a device that is already on. Refer to the Typical Characteristics curve "Turn-On/Off Response." Regardless of output capacitor size, output current on either output is limited to the value allowed by the threshold determined by the internal current limiting circuitry. Refer to the internal current limit threshold specifications stated in the Electrical Characteristics section of this datasheet. This permits very large output capacitors to be used. For example, USB ports are specified to have at least 120F of downstream capacitance from their controlling power switch. An output capacitance as large as 1000F would not disturb the input power supply to an AAT4626 used to control a USB port.
USB Dual-Channel Power Switch
active for more than approximately ten milliseconds, the FLG(A/B) pin is pulled to ground internally through an open drain device. The 10ms delay on the fault function is intended to prevent capacitive loads connected to one of the load switch outputs from activating its respective flag when the device is turned on. The placement of a pull-up resistor between the FLGA or FLGB pin and the IN pin is recommended. Reasonable values for the pullup resistor should range from 10k to 100k. Since the fault flags are open drain terminals, they may be pulled up to any voltage that is not greater than the level present on the IN pin. This is done to allow the AAT4626 to signal ancillary circuitry that is powered by voltage levels less than the level on the IN pin. If a fault flag delay greater than 10ms is required, addition delay may be added by use of an RC filter. As shown in Figure 1, an RC filter can be added to the fault flag output.
V+ 100k R1 10k 1 2 3 C1 0.1F 4
EN Inputs
The AAT4626 has two enable inputs, ENA and ENB. These two enable inputs allow the AAT4626 to independently control each respective output. The device is available in both active high EN enable and active low (EN) enable versions. For specific part numbers, refer to the ordering information section. When both the A and B outputs of the AAT4626 are in the off state, the respective outputs are an open circuit and the device quiescent current consumption is reduced to less than 1A. The ENA and ENB threshold voltages are set to allow the AAT4626 to be controlled by 5V TTL levels, as well as CMOS-compatible levels ranging from 2.5V to 5V. The ENA or ENB function control voltage levels should not exceed the input supply level applied to the IN pin.
USB Controller Over-Current Flag Input
AAT4626
ENA OUTA FLGA IN
8 7 6 5
FLGB GND ENB OUTB
Figure 1: Fault Flag Delay RC Filter.
Reverse Voltage
The AAT4626 is designed to control current flowing from IN to OUT. If a voltage is applied to OUT which is greater than that on IN, a large resulting reverse current may flow, potentially damaging the AAT4626.
Fault Flag Output
The AAT4626 features an active low fault flag (FLGA and FLGB) output for each A and B output channel. The fault flags are provided to alert the system if the over-current or over-temperature circuits become active, or if the load switch is not receiving a sufficient voltage level to properly operate. If either the current limit or overtemperature circuits in any combination are constantly
Under-Voltage Lockout
The AAT4626 has been designed with an under-voltage lockout control circuit. The under-voltage lockout prevents the output MOSFET devices from turning on until VIN exceeds the typical UVLO threshold of 2.3V. During operation, the device will automatically shut down if VIN falls below the UVLO threshold and the fault flags will be toggled.
4626.2008.02.1.3
www.analogictech.com
9
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Hot-Plug Applications
Application circuit cards with a high inrush current potential can be limited by use of the AAT4626. The AAT4626 has both slew rate limited turn on characteristics and current limit controlled outputs, which make it ideally suited for power port hot-plug applications. A host power back plane or hot-plug receptacle may be sensitive to short duration, high power surges. The AAT4626 will turn on in a linear ramping fashion and regulate the inrush current within the specified current limit for the device. The error flag usually will not be affected during application turn-on since the 10ms fault flag blanking time is intended for these types of events. If an application turn-on current surge exceeds 10ms, an RC delay filter may be added to the flag output to prevent the system from receiving an error during the start-up sequence.
USB Dual-Channel Power Switch
Refer to the following guidelines for power port PCB layout: 1. PCB traces should be kept as short and direct as possible to minimize the effects of the PCB on circuit performance. Make component solder pads large to minimize contact resistance. The AAT4626 output bulk capacitors and ferrite beads should be placed as close to the device as possible. PCB traces to the output connector should be kept as short as possible to minimized trace resistance and the associated voltage drop (I2R loss). If ferrite beads are used in the circuit, select ferrite beads with a minimum series resistance. The use of PCB trace vias should be avoided on all traces that conduct high currents. If vias are necessary, make the vias as large as possible and use multiple vias connected in parallel to minimize their effect.
2. 3.
4. 5.
PCB Layout Information
In order to obtain the maximum performance from the AAT4626, very careful attention must be considered in regard to the printed circuit board layout. In most port power switch and port protection applications, high voltage and current transient events will occur. Proper PCB layout can help reduce the effects of transient events. PCB trace resistance will effect overall circuit transient response; small voltage drops will also be incurred.
Evaluation Board Layout
The AAT4626 evaluation layout follows the recommend printed circuit board layout procedures and can be used as an example for good application layouts. (See Figures 4, 5, and 6.) Note that ferrite beads are not used on this simple device evaluation board. The board layout shown is not to scale.
Cable / Connector to Hot-Plug Port VBUS Hot-Plug Receptacle
V+
AAT4626
1 2 CIN 4.7F 3 4 ENA FLGA FLGB ENB OUTA IN GND OUTB 8 7 6 5
0.1F
Card Application Circuit A
CBULKA (120F) CBULKB (120F)
Card Application Circuit B
GND
GND
Dual Channel Inrush Current Protected Application Card
Figure 2: AAT4626 Input Inrush Current Protected Dual Output Application.
10
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
P-Channel MOSFET Switch On Resistance 0.09 (45mV)
IN OUTA
USB Dual-Channel Power Switch
Ferrite Bead and PCB Trace Resistance 0.02 (10mV) Cable, Connector and Contact Resistance 0.03 (15mV)
Trace Resistance 0.01 (5mV)
V+ Input Power Supply 4.50V to 5.25V GND CBULK
VBUS CBULK 0.1F GND
0.1F
Downstream Peripheral Port 500mA Max. Load Current
AAT4626 Ch. A
GND (10mV) (15mV)
(5mV)
Total Voltage Drop = 75mV
Figure 3: Summary of Typical Circuit Voltage Drops Caused by AAT4626 Circuit Components and PCB Trace Resistance.
Figure 4: AAT4626 Evaluation Board Component Side Layout.
Figure 5: AAT4626 Evaluation Board Solder Side Layout.
Figure 6: AAT4626 Evaluation Board Top Side Silk Screen Layout /Assembly Drawing.
4626.2008.02.1.3
www.analogictech.com
11
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Application Circuits
VBUS = 5.0V CIN 0.1F R1 100k R2 100k
7 IN OUTA 8
USB Dual-Channel Power Switch
Ferrite Beads
VBUS(A) COUT1 0.1F COUT2 120F D+ DGND
AAT4626
USB Controller On/Off A Error Flag A Error Flag B On/Off B 1 2 3 4 ENA FLGA FLGB ENB OUTB 6 5
DATA (Port A)
Ferrite Beads
VBUS(B) COUT3 0.1F COUT4 120F D+ DGND
DATA (Port B)
Figure 7: Typical Dual USB Host Port Application.
VCC +5.0V 0.1F AAT4626
ENA FLGA FLGB ENB OUTA IN GND OUTB
100k 4.50V to 5.25V Upstream V BUS 100mA Maximum VBUS D+ DGND 1F 100k AAT3200-3.3
IN OUT GND
3.3V USB Controller
VIN ON/OFF A Over Current A Over Current B
Ferrite Beads 120F 0.1F
USB Port A VBUS(A) D+ DGND
1F
ON/OFF B GND
Data 120F
Ferrite Beads
USB Port B VBUS(B)
0.1F
D+ DGND
Data A/B (Two Pair to USB Controller)
Figure 8: Self-Powered Dual Port USB Hub.
12
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
100k 4.50V to 5.25V Upstream V BUS 100mA Maximum VBUS D+ DGND 1F 100k AAT3200-3.3
IN OUT GND
USB Dual-Channel Power Switch
0.1F AAT4626
ENA FLGA FLGB ENB OUTA IN GND OUTB
3.3V USB Controller
VIN ON/OFF A Over Current A Over Current B
USB Port A Ferrite Beads VBUS(A) D+ DGND
120F
0.1F
1F
ON/OFF B GND
Data A Data USB Port B Ferrite Beads VBUS(B) D+ DGND
120F
0.1F
Data B
Figure 9: USB Bus Powered Dual Port USB Hub.
4626.2008.02.1.3
www.analogictech.com
13
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
Ordering Information
Package
SOP8 SOP8 TSSOP8 TSSOP8
USB Dual-Channel Power Switch
Enable
EN (Active-high) EN (Active-low) EN (Active-high) EN (Active-low)
Marking
4626-1 4626 4626-1 4626
Part Number (Tape and Reel)1
AAT4626IAS-1-T1 AAT4626IAS-T1 AAT4626IHS-1-T1 AAT4626IHS-T1
All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/about/quality.aspx.
Package Information
SOP-8
3.90 0.10 4.90 0.10
6.00 0.20
0.375 0.125 1.55 0.20
45
0.175 0.075
4 4
0.235 0.045 0.825 0.445
0.42 0.09 x 8
1.27 BSC
All dimensions in millimeters.
1. Sample stock is generally held on part numbers listed in BOLD.
14
www.analogictech.com
4626.2008.02.1.3
PRODUCT DATASHEET
AAT4626
SmartSwitchTM
TSSOP-8
USB Dual-Channel Power Switch
4.40 0.10
6.40 0.20
3.00 0.10 0.65 BSC
12 REF x 4
1.05 MAX
1.20 MAX
0.145 0.055 4 4
0.245 0.055 x 8
0.10 0.05 12
0.60 0.15 1.00 REF
DETAIL A
All dimensions in millimeters.
Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611
(c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech's terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders.
4626.2008.02.1.3
www.analogictech.com
15

▲Up To Search▲

Price & Availability of AAT462608

	To Download AAT462608 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .